Topic guide
Browse references on commissioning, test planning and system verification. Review the test scope, acceptance conditions and documentation requirements alongside your project’s technical requirements.
25–48 / 66
Open Compute Project Foundation 2024
Store CDU capacity in the catalogue using this rating basis (kW at 5 C ATD, 1.5 LPM/kW, head and FWS impedance) so units from different vendors can be compared, and derate when the design ATD or flow differs.
7x24 Exchange Magazine 2024
Generate a commissioning test plan from the design: one load bank test entry per genset (resistive-inductive at rated kVA).
IEC 2016
In a commissioning module, generate an initial-verification test schedule per circuit from the design model: continuity, insulation resistance, polarity, fault-loop impedance and RCD tests.
Mortenson 2024
In the phasing module, model staged handovers with live-side/build-side separation.
NFPA 2025
In the generator module, capture the EPSS class (fuel run time), type (start time) and level on the generator object and size fuel storage to the class.
Vertiv 2019
Add a delivery-method attribute per block (stick-built, skid, power module, prefab room/facility) with factory-test status and shipping-split count.
Open Compute Project Foundation 2025
Define a 2 MW CDU catalogue template for liquid-cooling layouts: dimensions, wet weight (6910 lb) for slab loading, 74 kW parasitic load, 3 C approach and 0.25 GPM/kW facility flow.
U.S. DOE Federal Energy Management Program / Lawrence Berkeley National Laboratory 2011
Add a retro-commissioning checklist to the commissioning module: reheat lockout, redundant unit staging and setpoint reset.
Schneider Electric 2026
Keep design intent as first-class, exportable data: redundancy zones, operating modes, density limits, tier target and control philosophy attached to the model, not notes.
Schneider Electric 2016
In the monitoring design module let users scope BMS, EPMS and DCIM separately and assign each monitored asset (chillers, CRAHs, UPS, PDUs, rack PDUs) to one system with a protocol (BACnet IP/MS-TP, Modbus TCP/RTU, SNMP).
Schneider Electric 2015
Let users define a reusable power/cooling/rack module and replicate it across phases and sites, with BOM and labelling generated consistently.
Energies (MDPI AG) 2019
Calculate the permissible time for a cooling outage with a pipe-volume energy balance and set the backup-cooling start time accordingly (here 300 s); high-temperature, contained designs give less time.
Vertiv 2026
Give the rack/pod model a liquid fraction (default about 70% for direct-to-chip) so residual air load is computed automatically.
Türk Tesisat Mühendisleri Derneği (TTMD) - TTMD Dergisi 2026
Offer sparse-sensor temperature-field reconstruction in monitoring and digital-twin features as a fast alternative to CFD, flagged as model-based.
7x24 Exchange Magazine 2024
Link each electrical study type in the tool (short circuit, load flow, protection coordination, grounding) to its IEEE reference in tooltips and report headers.
TMMOB Makina Mühendisleri Odası (MMO) 2023
In the catalogue, add test-standard and witness-test fields for IEC/DC AHUs: ASHRAE 143 rating, tested capacity, factory witness test yes/no.
TMMOB Makina Mühendisleri Odası (MMO) 2025
In the commissioning module, include a TAB task list per cooling unit and hydronic circuit (design versus measured airflow, water flow, differential pressure, set points).
Schneider Electric 2026
In the schedule estimator, default MV switchgear lead time to about 26-32 weeks (ETO)
Eaton 2016
Add a designLifeYears catalog parameter per equipment type, default to the range midpoint, and drive a TCO/refresh timeline from it.
IEEE (Energy Efficient HPC Working Group paper; hosted by Lawrence Berkeley National Laboratory) 2021
Use the eight-section outline as the skeleton for the controls part of an Owner's Project Requirements before the Basis of Design starts.
Lawrence Berkeley National Laboratory 2014
Borrow the metric set (PUE, intake temperature and humidity, RTI, cooling efficiency, airflow efficiency, distribution efficiency) as the minimum list of measurements a monitoring design must support.
Open Compute Project Foundation 2024
Reserve space for tap-off valves, pipe paths with straight runs, valve and fitting replacement, drainage and condensation collection in the original design.
Schneider Electric 2011
Default the commissioning budget to about 2% of capex.
Schneider Electric 2011
In the project-workflow feature, provide a RACI template with roles per phase (Prepare/Design/Acquire/Implement/Operate).
All content and rights belong to the respective authors and publishers. SoSo CAD provides only the citation, its own summary and a link to the source, and is not responsible for the sources' content.
Monthly newsletter · free
Once a month: new library sources, changes to Turkish regulations and upcoming data centre events.
