Collection
Technical references added to the library in the last 90 days.
1009–1032 / 1044
U.S. DoD (UFC) 2020
Set battery room scope by NFPA 1 (all stationary batteries of 48 VDC and above), put different chemistries in separate rooms, and avoid unrelated services and direct access; do not use the room for storage.
U.S. DoD (UFC) 2023
Include transient and steady-state loads, transformer inrush, motor starting and UPS load in the generator sizing study, and calculate UPS charging load using the minimum charging current allowed while on generator.
U.S. DoD (UFC) 2019
Settle the loop or alternate-feed arrangement and the maintenance isolation points for the MV run from utility entry to the building early; the text treats shortening maintenance outages as a direct design driver.
U.S. DoD (UFC) 2021
Build the data hall protection concept in this order: very early warning smoke detection, wet-pipe sprinklers throughout, clean agent only as an addition, and state in the specification that clean agent cannot replace the sprinklers.
U.S. DoD (UFC) 2024
On the site plan check the minimum standoff between the security line, clear zone and building (20/50 ft) and the 33 ft unobstructed space; define for outdoor chillers, generators and fuel tanks a no-concealment layout or a four-sided enclosure.
Schneider Electric 2024
Add BESS as a site energy asset with kW, kWh and chemistry inputs
Vertiv 2021
Rule: rack kW > 20 suggests containment plus in-row cooling or rear-door heat exchangers; rack kW > 30-40 recommends liquid.
Schneider Electric 2021
Give the battery catalog these fields: chemistry, mass per kWh, design life, replacements over UPS life and recycling rate.
POWER Magazine 2024
Use it as a negative test case: the app's Tier explanations must not hard-code availability percentages or equate Tier IV with '2N+1'
Lawrence Berkeley National Laboratory 2016
Use the space-type PUE table as a sanity check on early-stage PUE assumptions, remembering these are 2014 national averages, not design targets.
Uptime Institute 2026
Weight UPS, ATS/STS and generator failure modes highest in the reliability model
Uptime Institute 2025
Use PUE 1.54 as the 'industry average' line on the efficiency dashboard, year-stamped and user-overridable
Uptime Institute 2026
Make 30 kW/rack the threshold where the app moves from 'enhanced air' guidance to 'liquid-ready' guidance (rear-door heat exchanger / direct liquid cooling)
Uptime Institute 2026
Add a three-gate certification pathway to the project plan, starting with a TCDD-like design review before construction drawings freeze
Uptime Institute 2026
Model 'reliability.target' as an enum {TierI..TierIV} driving topology defaults: Tier I single path N; Tier II N+1 capacity components, single path; Tier III N+1 components AND two distribution paths (one may be passive), concurrently maintainable; Tier IV 2N or 2(N+1), two active physically compartmentalized paths and continuous cooling with UPS-backed pumps/fans.
U.S. DOE FEMP / NREL 2019
Arrange the heat-rejection hierarchy as in the scheme: heat reuse first, then dry cooling, evaporative towers last; write the control logic in that order.
Vertiv 2025
Seed an AI-hall wizard template with: compute rack 73 kW, support rack 14 kW, liquid fraction 0.78, power 4N/3, cooling N+1, mechanical UPS 2N.
Vertiv 2024
Provide a "2N AI hall" preset to compare with the 4N/3 preset: 2N makes installed UPS 200% of load against 133% for 4N/3; show the capex and efficiency deltas.
Vertiv 2025
Make the capacity block a first-class object: block = UPS group + PDUs + CDUs + chillers sized for N pods, so no power is stranded.
Vertiv 2025
Implement mechanical UPS sizing explicitly: mechUpsKw = sum of CDU pump kW + CRAH fan kW for every unit that must ride through; default about 20 kW per 1.35 MW CDU (roughly 1.5% of liquid load) and about 17 kW per CRAH.
Vertiv 2025
In the campus planner define the 2,496 kW pod as a repeatable block; when the user picks N blocks, multiply UPS, CDU and chiller counts by the block count.
Vertiv 2024
In the layout engine add 200 mm to rack depth for liquid-cooled AI racks; manifolds and hoses do not fit standard depth.
Schneider Electric 2026
Compute and display WUE (L/kWh IT) next to PUE for every cooling design.
ASHRAE TC 9.9 2019
Enforce TCS supplyTemp >= roomDewPoint + 2 degC.
All content and rights belong to the respective authors and publishers. SoSo CAD provides only the citation, its own summary and a link to the source, and is not responsible for the sources' content.
Monthly newsletter · free
Once a month: new library sources, changes to Turkish regulations and upcoming data centre events.
